The subject-matter of the contract covers the supply and assembly of a welding workshop – didactic equipment necessary to conduct training in the profession of ‘Electric vehicle mechatronics’ in accordance with the scope set out in Annex 1a to the SWZ. The technical, quality, functional and performance characteristics shall not be worse than those listed in Annex 1a to the RVU. The device should meet all regulations regarding the right to be allowed to use in Poland and have appropriate documents proving that it meets all the necessary standards and guidelines that the equipment should meet before it is allowed to use. The appliance must be accompanied by all the necessary documents of the type: instruction manual, warranty, statement of compliance with all necessary standards, etc. The ordering party requires that the delivered equipment be brand new, unused. If signs or parameters indicating a specific manufacturer, a specific product or trademarks, patents or origin are used to describe the subject of the contract, the Ordering Party allows the use of equivalent products, which should be understood as a product with technical, functional and quality parameters not inferior to those presented in the description of the subject of the contract. An economic operator who submits a tender for an equivalent product must attach to the tender a precise description showing that the conditions of equivalence will be complied with; it must also demonstrate (prove) that the proposed solution satisfies the requirements specified by the Contracting Authority to an equivalent extent, in particular with regard to the indicated parameters. The Contractor undertakes to: • ensure safe transport and delivery of the subject-matter of the contract, • install the equipment and, if applicable, make it operational, • configure and verify (to the extent appropriate to the type of equipment), • provide all required connection cables and wires, accessories, installation elements, etc. necessary for the installation/assembly of the equipment (if applicable), • provide the designated persons of the Contracting Authority with the necessary information on the operation of the equipment (if applicable). The subject of the contract includes the supply and installation of didactic equipment for the needs of equipping the workshop of industrial machines and equipment located in the Industry Skills Center in Wałbrzych in the field of mechatronics, ul. Ogrodowa 2a, 58-306 Wałbrzych. Information on the means of proof in question confirming that the supplies offered meet the requirements specified by the Ordering Party. In order to confirm that the deliveries meet the requirements specified by the Ordering Party, the Ordering Party requests that the Contractor together with the offer present: 1. a statement on the compliance of the subject of the tender with the description of the subject of the contract. The declaration should show, without any doubt, that the proposed assortment is of the same or better technical, quality, functional and utility parameters in relation to the assortment specified by the Ordering Party – the model declaration is attached as Annex 1a to the SWZ. The Contracting Authority informs that if the evidence is not submitted or if the submitted evidence is incomplete, the Contracting Authority will call on the Contractor to submit or supplement it. The contracting authority shall not allow partial tenders to be submitted. - the scope of the subject-matter of the contract allows SMEs to participate in the procedure, - the plan of procedures does not provide for the division of the contract into lots, - the subject-matter of the contract requires uniform guarantee protection, - the division of the contract may result in excessive costs of performance of the contract and excessive technical difficulties, - the activities of various contractors performing individual parts of the contract may seriously jeopardise the proper performance of the contract. The Contracting Authority does not allow the submission of variants and electronic catalogues. The contracting authority does not provide for the award of contracts referred to in Art. 1 point 7 of the PPL. Wherever specific standards and regulations are referred to in the contractual documents to be met by materials, equipment and other goods and works performed and examined, the provisions of the most recent edition or revised edition of the said standards and regulations shall apply, unless otherwise provided in the terms of the contract. Where the standards and regulations invoked are national or relate to a specific country or region, other appropriate standards ensuring an equivalent or higher level of performance than the standards or regulations invoked may also be applied, subject to their verification and written approval by the contracting authority. The differences between the standards referred to and their proposed replacements must be described in detail by the Contractor and submitted to the contracting authority for approval. The project received funding from the National Recovery and Resilience Plan (NRRP), concerning the implementation of the task under the Competition entitled: "Establishment and support of 120 Industry Skills Centres (BCUs)" implementing the CoVEs concept. The subject of the contract as teaching equipment must enable the implementation of the core curriculum for the profession of mechatronics. Legal basis: Regulation of the Minister of National Education of 16 May 2019 on the core curriculum of education in the professions of sectoral education and additional professional skills in the field of selected professions of sectoral education (Journal of Laws 2019.991 as amended)
Text automatically translated in your browsing language
Automatically translated
